Ra & RMS: Calculating Surface Roughness

Ra & RMS: Calculating

Choose your Formula to Calculate Surface Finish

RA
View Ra Calculation
What Does Ra Mean?

As described in ASME B46.1, Ra is the arithmetic average of the absolute values of the profile height deviations from the mean line, recorded within the evaluation length. Simply put, Ra is the average of a set of individual measurements of a surfaces peaks and valleys. Reveal the Ra formula for more insight.

RMS
View RMS Calculation
What Does RMS Mean?

As described in ASME B46.1, RMS is the root mean square average of the profile height deviations from the mean line, recorded within the evaluation length. Reveal the RMS formula for more insight.

Reviewed by Tom Harrison, member of the ASME BPE Surface Finish Subcommittee · Updated November 2026

The short answer: Ra is the arithmetic average of the surface profile's deviations from its mean line; RMS is the root mean square of the same readings. For a typical machined or polished surface, RMS runs roughly 10–11% higher than Ra (RMS ≈ 1.1 × Ra), so a 16 µin Ra surface reads about 17.6 µin RMS. Most current specifications, including ASME BPE and ASTM B46.1, call out Ra. If a drawing gives RMS, convert it before you quote the finish.

What is the difference between Ra and RMS?

Ra and RMS are both representations of surface roughness, but each is calculated differently. Ra is calculated as the Roughness Average of a surfaces measured microscopic peaks and valleys. RMS is calculated as the Root Mean Square of a surfaces measured microscopic peaks and valleys. Each value uses the same individual height measurements of the surfaces peaks and valleys, but uses the measurements in a different formula. The formulas are shown below. One can infer from examination of the formulas, that a single large peak or flaw within the microscopic surface texture will effect (raise) the RMS value more than the Ra value.

The electropolishing process may improve a surface finish by up to 50%. The electropolishing reaction removes material while it improves surface roughness. Because of the material removal, process runtimes are often limited to maintain dimensional tolerances. Limited runtimes result in real world surface roughness improvements from 10 to 35%. Remember, electropolishing improves a surface on the microscopic level. If a material has a texture or surface scratch, electropolishing will only result in a lustrous texture or lustrous scratch. Mechanical polishing is utilized to remove macroscopic texture or blemishes.

The formulas

Both use the same n height readings (y1 … yn) measured from the mean line by a profilometer.

Ra = (1/n) × Σ |yi| — the average of the absolute heights.

RMS (Rq) = √[(1/n) × Σ yi2] — the square root of the average of the squared heights.

Because RMS squares each reading, one deep scratch or high peak raises RMS more than Ra. That is why two surfaces with the same Ra can have different RMS values, and why Ra alone does not describe surface condition.

Have a drawing with an Ra or RMS callout? Send it and we'll confirm what finish is achievable from your starting surface, with a profilometer report on every part.

Send Us Your Drawing or call 800-245-5707, Mon–Fri 7–5 Central.

Related: ASME BPE SF1–SF6 Finishes · Stainless Steel Electropolishing · Mechanical Polishing

Looking for #4, 2B, #8, etc. Stainless Steel Finish Capabilities?

The above finishes are some of many mechanical finishes which are often used in the metal finishing industry. Both the NiDi No. 9012 and previous revisions of ASME BPE specifications include a list that describes various mechanical surface finishes for stainless steel.

Learn more about our Stainless Steel Electropolishing capabilities

Equivalent Ra values for Surface Finish Grade Numbers

Older drawings may use roughness grade numbers to indicate Ra values. The following table is given in ISO 1302:1992.

Roughness N
ISO Grade Numbers
Roughness values Ra
micrometers (µm)
Roughness values Ra
microinches (µin.)
RMSCLA (µin.)
Center Line Avg.
Rt
Roughness, microns
N12 50 2000 2200 2000 200
N11 25 1000 1100 1000 100
N10 12.5 500 550 500 50
N9 6.3 250 275 250 25
N8 3.2 125 137.5 125 13
N7 1.6 63 64.3 63 8.0
N6 0.8 32 32.5 32 4.0
N5 0.4 16 17.6 16 2.0
N4 0.2 8 8.8 8 1.2
N3 0.1 4 4.4 4 0.8
N2 0.05 2 2.2 2 0.5
N1 0.025 1 1.1 1 0.3

Frequently asked questions

What is the difference between Ra and RMS?

Ra is the arithmetic average of the absolute surface profile heights from the mean line. RMS is the root mean square of the same heights. RMS is typically about 10 to 11 percent higher than Ra for the same surface because squaring the readings weights peaks and scratches more heavily.

How do you convert Ra to RMS?

For most polished or machined surfaces, RMS is approximately 1.1 times Ra. A 16 microinch Ra surface reads about 17.6 microinch RMS. The ratio varies with the surface texture, so the conversion is an estimate, not an exact equivalence.

Which should I specify, Ra or RMS?

Specify Ra. Current standards including ASME B46.1 and ASME BPE use Ra. RMS appears mainly on older drawings.

How much does electropolishing improve Ra?

Electropolishing can reduce Ra by up to 50 percent. In practice, runtimes are limited to hold dimensional tolerances, so real-world improvements are usually 10 to 35 percent. Harrison reports the starting and finished Ra on request.

What Ra does an ISO roughness grade number equal?

ISO 1302 grade numbers map to Ra values. For example N5 equals 0.4 micrometers or 16 microinches Ra, N4 equals 8 microinches, and N3 equals 4 microinches. The full table is on this page.

Electropolishing

Harrison Electropolishing, the Leading Electropolishing, Passivation, Oxygen Cleaning & Mechanical Polishing Company World Wide.

Electropolishing is an electrochemical process by which surface material is removed by anodic dissolution. Electropolishing removes surface material, beginning with the high points within the microscopic surface texture. By removing these points, the electropolishing process will improve the surface finish of a metal such as stainless steel, nickel, and Hastelloy, leaving a smoother and more reflective surface. Common parts and components electropolished include tanks, piping, fittings, rods, discs, large parts & surfaces, and more.